Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
What are your thoughts with regards to Installing A Bathtub?
Setting up a bath tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old tub is easily obtainable, the job can relocate rapidly; if you have to open up a wall surface to remove the old bathtub and also position the new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old tub and also embeded in the new one. Ensure you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider using one prior to you start. Chances are you may need an expert plumber to make tube links.
This short article will assist you install a brand-new bathtub in your shower room if you have currently bought a new tub and don't need to change the plan of your previous supply of water pipelines.
Your devices and also product list should comprise the following:
Getting ready for the Installment
Firstly, the supporting structure provided with the bath needs to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be quite problematic because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level reads level.
To set up faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the water system as well as examine all joints and new pipework for leaks as well as tighten them if required. Fill the bath tub as well as likewise examine the overflow outlet and the typical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and securing around the tub ought to wait up until the tub has actually been utilized at least once as this will certainly settle it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the faucet in place with the maker supplied backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type needs to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, leading to problems with wetness and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly load the bathtub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture rather very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub? Leave feedback further down. We would be delighted to listen to your views about this piece. We hope that you visit us again before long. Enjoyed our blog posting? Please share it. Help others discover it. Thank you for your time. Visit again soon.
We're ready, are you? Report this page